Can A Sempron 3000 Really Overclock This High
I have no idea what this means, but this is what I want to do. Even on my stock amd unlapped hsf and thermal pad, i'm doing fairly well. Second, i could only get it to sucessfully complete super pi at 2. 6ghz at about 1. 44-1. 56v, according to cpu-z. Also some suggestions about what I should do to minimise these side-effects (such as giving my computer half hour cooling breaks every couple of hours) The decrease should be fairly minimal,
I think I will check to see what kind of idle temps I'm really getting later and post another screen shot after I've let my PC idle for a while. You can compare things here to get an idea of where you stand: http://hwbot.org/hardware/processor/...tab=2drankings Pay attention to the cooling used with each chip listed, better cooling methods almost always = high But oddly it boots just fine with these settings if I set them in CMOS and then try to boot up immediately after setting them. The last two characters within the model string that identifies it as a Newcastle would be AX - It helps to know what you're ordering because that site sometimes doesn't give http://www.tomshardware.com/answers/id-2261233/overclocking-amd-sempron-3000-bit-processor.html
- View Related Posts . .
- Welcome to OCF!
- You know, I've been trying to find a program that would do readouts of my NB's temperature, but I haven't been able to find one yet.
- Copyright ©2000 - 2014, iNET Interactive Overclockers.com Register New Posts Advertising Contact Us Archive Sitemap Top Hosting and Cloud Web Hosting Talk HostingCon WHIR Hosting Catalog Hottest Hosts Data Centers Data
- Is there a way too prevent this from happening?
- if this is a socket 939 board - you can check with MSI what CPUs are supported in this board change processors to an Athlon X2 (if supported) also as Doom
- Melde dich bei YouTube an, damit dein Feedback gezählt wird.
- McCoy; 01-15-11 at 01:49 AM.
- I'd also try a CPU voltage of 1.45v's since that's not much higher than you had set it already and as long as it stays under 55C under load it should
- Posted On: October 9th 2005 .
Upping the VCore to 1.425 was even worse, and the lowest it hit at that setting was 1.44V. I have bought several chips from them in the past and so far, so good. Powered by vBulletin Version 4.2.2 Copyright © 2017 vBulletin Solutions, Inc. No one comes to the Father but through me." John 14:6 Reply With Quote 01-15-11,01:27 AM #15 Dr.
Posted On: April 14th 2006 . If this is a pre-built system some of the cpu settings may not be available. Will Amd Athlon Ii Bottleneck Gtx 465 ? http://forum.egosoft.com/viewtopic.php?t=180984 View Related Posts . .
Posted On: 2 months ago . When upping the mhz my mem and ht changes as well. View Related Posts . . Gained 300 MHz of speed on the CPU and 70 MHz on my RAM, and nothing blew up or fried *knocks on wood*. \m/ OverClockers mATX L33T Club \m/ Main Rig:
Yes, I'd actually been doing some searching on ebay for the last month or two. http://www.xbitlabs.com/articles/cpu/display/sempron-3000_10.html no. Overclocking Amd Athlon Xp 3200+ Is this pretty much pointless, or is it something worth while? It's quite likely that you'll change the CPU / PC anyway long before the chip fails._________________Strung out on Britain's high, hitting an all time low Back to top andrewas Joined: 10
If your motherboard is supported, check out clockgen by the makers of cpu-z. Of course, before long i'm tempted to overclock it, even just a little. View Related Posts . . McCoy View Profile View Forum Posts Member Join Date Feb 2010 Location Alabama 37-39C at idle indicates a cooling issue.
It has a decent to good stepping (E6) so that shoudn't be much of an issue but it should be capable of more speed than shown. If wanting to go further with the system itself, I'd start looking for something along the lines of a Venice, Newcastle or similar chip. Overclocking 3700+ San Diego Athlon 64 Ive got a 3700+ san diego athlon 64. Yes, you'd probably need a better way of cooling it to go much further.
I lowered my memory speed to 166mhz and still nothing. Jun 07, 06:17 Post subject: check the manual of your MoBo how to set your "jumpers" for overclocking, than in your Bios set the option "Core CPU speed" (or alike) to If you have to, just try a divider to slow your RAM down to keep it within it's limits.
Those 300 extra MHz I got are pretty good, but I'd like more.My CPU is on an Asrock K8NF6G-VSTA motherboard.
In particular, find a beginners guide which covers how to determine how far you can go, and how to verify that the system is stable afterwards . If this is your first visit, be sure to check out the FAQ by clicking the link above. Temps for the CPU are within tolerance as you pointed out but just barely. But with the CPU running at 2.12 GHz, the temperature doesn't go above 52 degrees; the maximum temperature i get with its standard frequency is 50 degrees, so i think the
Your setting shown as NF4 voltage is your chipset voltage setting. Full Review ViewSonic VX2757-MHD 27-inch 1080p Gaming Monitor with 2ms, VGA,... Hinzufügen Playlists werden geladen... And...
If you choose the 166MHz divider, then it becomes 200MHz FSB/166MHz RAM, this difference of 34MHz will remain consistent as long as you continue to run the 166MHz divider. Posted On: February 26th 2006 . Amd Processor 3000 Or Intel Pentium 4 What processor is better amd processor 3000 or intel pentium 4? I am using the stock HSF though, so I'm not really anticipating breaking any records with this thing, except for maybe my own. \m/ OverClockers mATX L33T Club \m/ Main Rig:
With the CPU running at 100% for around 10 minutes, the temperature didn't get above 90 degrees. (I opened SIV Beta then to see my GPU temperature and i noticed that But ne ways i tried to over clock my cpu but it cant go over 210 fsb. I was wondering which processor was betting, an amd athlon 3800+ or an intel pentium d 805 and i was also wondering. Reviewed by NoelC I've had one of these cards in Dell Precision T5400 and T5500 Workstation systems since 2012, controlling RAID 0 arrays of four OCZ 480 GB Vertex 3 SSDs
I don't want to overclock my video card. I'm wondering if it's worth buying a 3400+/3700+ or is it better to overclock my current cpu ?